FireBlade_FPV

Pushing the range a little further with the new system. Running the full version of the TBS Crossfire TX and the TBS Nano receiver. TBS XFire transmitter is set at 100mw here, and VTX is set at 200mw. Getting a bit of lines in the video when I go above 100mw on the VTX. Will try to insulate and isolate the signal wires and antenna a little better, might help. https://youtu.be/7l_fwsfwMfc Running the Omnibus F4 Pro V5 FC with Betaflight 3.5.7 Typhoon 32 V2 35A 4-in-1 DShot1200 ESC RunCam Racer 2 FPV camera TBS Crossfire system TBS Unify system iFlight XING 2207 1700kv motors GNB 1300mah 6s 120c packs FrSky Taranis X9DPlus FatShark Dominator V3 with FuriousFPV True-D V3.7 receiver and ImmersionRC and iFlight antennas RHCP Discord user: FireBlade#4248 Discord server: https://discord.gg/aRagMuJ https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #midrange #fpv #iFlight #XING #tbsblacksheepfpv #tbscrossfire #tbsunifypro #fireblade_fpv

https://youtu.be/OBWZYEYeZdc Lunch time and had a chance to whoop some fun trains and semi trucks on a great day. Trains were not moving at the time but the semi trucks sure where ! Almost flattened right off the bat, but I heard the truck behind me so I knew it was coming, luckily LOL. Getting some breakup in the video feed here but not bad, wifi is all over the place at this location. I was here actually taking some overhead shots with the 5" racer, using the session 5 to capture high res still images, actually turned out really great. I was able to get some really nice downward angles. Flying the 65mm brushless whoop from Mobula 0608 19,000kv motors from Happymodel 31mm four blade props from BetaFPV 450mah 80c 1s LiHV packs from GNB Fat Shark Dominator V3 with FuriousFPV True-D V3.7 Receiver and ImmersionRC and iFlight antennas Discord user: FireBlade#4248 Discord Server: https://discord.gg/aRagMuJ https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #tinywhoop #mobula #snapper #betaflight #fatshark #fireblade_fpv

https://youtu.be/4EtcTumsnbQ Trees are awesome ! especially these trees, perfect for close proximity flying :) This field and area are so fun, I post a lot of footage from here but can't help it. I will get to some new spots very soon, a couple of events coming up quick. Two big events in June, a few in July and a big competition in August. Going to be a crazy summer ! I'm working on a few builds right now, some new goodies. Trying out some 6s all-in-one esc's and some new cameras and motors. Oh and some different batteries to try, I ordered several different 6s models, will give them a try and see how they do. Working on the tune here as well, some propwash in some spots but overall very happy with the tune. Updated to Betaflight 4.0.2 last weekend and did a retune, see the video here; https://youtu.be/edMCzrtE0JA OmniBus F4 Pro V4 FC Betaflight iFlight iPeaka 45a DShot1200 ESC iFlight XING 2306 2450kv motors TBS Crossfire Full TX and Nano RX TBS Unify Pro VTX FrSky Taranis X9D Plus Fat Shark Dominator V3 with FuriousFPV True-D V3.7 and ImmersionRC and iFlight antennas Discord user: FireBlade#4248 Discord server: https://discord.gg/aRagMuJ https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #tbscrossfire #tbsunifypro #betaflight #iflight #fireblade_fpv #XING #teamblacksheepfpv #noedit

https://youtu.be/m6JIphHk2Qw Flying the 65mm brushless micro quadcopter at work over the holiday weekend. A few of us had to come in for inventory, so I brought the little guy with me to fly during lunch. I've flown in this office in the past so they are used to my antics, the little 65mm is so tiny they all just laugh at it. I still have a lot of fun with this micro, I've had it almost six months and have really beat it up and still going on original frame. Need more power and more flight time, looking at the Beta65x or the Beta75, or a CineWhoop :)  65mm Brushless Tiny Whoop from Mobula 0603 19,000kv brushless motors from Happymodel Four blade 31mm props from BetaFPV CrazyBee F4 Betaflight 3.5.7 Fat Shark Dominator V3 with FuriousFPV True-D receiver and ImmersionRC and iFlight antennas Discord user: FireBlade#4248 Discord server: https://discord.gg/aRagMuJ https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #tinywhoop #mobula #betaflight #happymodel #fireblade_fpv #whoop #betafpv 

https://youtu.be/edMCzrtE0JA Time to update BF and tune with my 210mm race quad. I held off updating right away when Betaflight 4 first came out. I'm very happy with my tune on 3.5.7 and was not in a rush to move to this new and very different version. I've heard and read a lot about the new filters and changes to PID loop and other additions so will eventually need to get on it. I left everything default, all filters and PID settings are BF 4.0.2 settings. The only changes I made were to the rates, and very minimal. I lower RC rate just a bit, down to .9 on all axis. I also add .4 expo to all axis, including throttle and I also zero out throttle mid. First thing I noticed was that the tune was much closer to how I like it right out of the box. PID settings are very close, and much of this can most likely be contributed to improved filtering and the addition of D_Min and I term relax. I notice that the I term default settings are much higher than in previous builds, especially yaw. I ended up adding just a touch of P on all axis and backing off I term on yaw just a bit. Very, very close though without changing anything, and that seems to be what BF is going for. Seems very nice, now the real test, take it to some events :) going to be a great summer !! Hope this video helps and comment with any questions. My build; Lumenier QAVR 210 frame all soft mounted (ESC, FC and Motors) iFlight iPeaka 45a DShot1200 ESC iFlight XING 2306 2450kv motors topped with Ethix Watermelon blades TBS Crossfire Nano SE RX with Immortal T antenna TBS Unify Pro 5v VTX with iFlight stubby RHCP antenna RunCam Robin FPV Cam GoPro Session 5 - 2.7k Superview - No Stabilization FrSky Taranis X9D Plus with Standard TBS Crossfire Module Fat Shark Dominator V3 with FuriousFPV True-D receiver and ImmersionRC and iFlight antennas Discord user: FireBlade#4248 Discord server: https://discord.gg/aRagMuJ https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #betaflight #iflight #crossfire #unify #teamblacksheep

https://youtu.be/7io0QQm-LpA Had the chance to fly around in a brand new constructed office building ! What a great building, and perfect for flying :) The office is not open for business yet so I had to take the opportunity while I could. Everyone was great about it, loved the tiny little whoop. The area upstairs where I'm standing is the data room we setup and computer lab. The data room is closed, I should have left the door open and flew in the room, but not much to see in there anyway. Would be perfect for setting up whoop gates everywhere !! 65mm Mobula 6 Brushless with HappyModel 0603 19,000kv motors Betaflight 3.5.7 4 blade 31mm props from BetaFPV  Fat Shark Dominator V3 with FuriousFPV True-D receiver and ImmersionRC and iFlight antennas. https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #tinywhoop #mobula #betaflight #fatshark #whoop #snapper #fireblade_fpv #furiousfpv #immersionrc #microfpv 

https://youtu.be/G2v_OomiUPs Sorry took so long to post this, once I received the package I became very distracted LOL. I don't want to give away what the shipment contained before watching some video, no spoiler !! A few great FPV products here, probably my single largest purchase in the hobby and the most necessary. Thank you Jesse HighAfpv and Jesse at Krazy Kwads for hooking me up with a great deal and some extra goodies :) Check them out at http://www.KrazyKwads.com Thank you and keep watching for build video coming soon !! https://www.YouTube.com/user/JDogB1 https://www.AirVuz.com/user/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV #betaflight #fpv #krazykwads #teamblacksheep #tbscrossfire #tbsunify

https://youtu.be/uTFsZfbmrq4 Putting in some time on the new gimbals, love the X9D plus. Will run these for some time then eventually swap out for a set of Hall Gimbals. Practicing at one of my favorite spots during lunch, put in three packs if I remember right. Getting nice warm outside, have missed the sunshine very much. Also testing the Runcam Robin here, micro FPV camera running 5v Testing my TBS Crossfire as well as my new TBS Unify Pro 5v VTX, all working perfect :) Thank you Albeesoaring and http://www.KwadGarage.net for getting me setup with the awesome custom gimbal guards and antenna protectors ! Thank you http://www.KrazyKwads.com for the Radio setup ! iFlight XING 2306 2450kv motors with iFlight iPeaka 45A DShot1200 esc and topped with Ethix Watermelon blades OmniBus F4 Pro V4 Betaflight 3.5.7 TBS Crossfire Nano receiver with Immortal T antenna GoPro Session 5 at 2.7k 30fps Superview - no stabilization Fat Shark Dominator V3 with FuriousFPV True-D V3.7 receiver and ImmersionRC and iFlight antennas https://www.AirVuz.com/user/FireBlade https://www.FPVBook.com/FireBlade https://www.InstaGram.com/Jason_FireBladeFPV Check out Albeesoaring's page here: https://www.youtube.com/channel/UCmTEpb6RdCIXIXnBrlJ8RGQ #taranis #frsky #tbscrossfire #tbsunifypro #betaflight #fireblade_fpv #teamblacksheepfpv